Wasp-barcode WLS8600 Product Reference Guide Manuel d'utilisateur télécharger pdf (Page 19)

CONFIGURATION

USB

USB-KBD

Ì$+UA03$-:Î

USB-KBD-ALT-MODE

Ì$+UA04$-@Î

USB-KBD-APPLE

Ì$+UA05$-FÎ

USB-COM*

Ì$+UA02$-4Î

USB-IBM-Table Top

Ì$+UA00$-(Î

USB-IBM-Hand Held

Ì$+UA01$-.Î

* When configuring USB-COM, the relevant files and drivers must be installed from

the USB Device Installation software. Contact WASP Technical Support for more

information.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 143 144

Reference Manual 1
CONTENTS 3
GENERAL VIEW 6
1 INTRODUCTION 7
2 INSTALLATION 8
INSTALLATION 9
CAUTION 9
2.2 RS-232 CONNECTION 10
2.3 USB 10
2.4 IBM USB POS 10
2.5 WEDGE CONNECTION 11
3 CONFIGURATION 12
3.2 SETUP PROCEDURES 13
Ì$+CP0$-$Î 15
Ì$+CM2EC0$->Î 15
Ì$+CM1$-ÈÎ 15
Ì$+CM0$-ÃÎ 15
Ì$+CP6$-BÎ 15
First Start-Up 18
RS-232 PARAMETERS 21
BAUD RATE 22
DATA BITS 23
STOP BITS 23
HANDSHAKING 23
ACK/NACK PROTOCOL 24
INTER-CHARACTER DELAY 24
RX TIMEOUT 25
SERIAL TRIGGER LOCK 25
USB PARAMETERS 26
USB-COM 27
USB-KBD 29
KEYBOARD NATIONALITY 29
INTER-CODE DELAY 31
USB KEYBOARD SPEED 31
WEDGE PARAMETERS 32
CAPS LOCK 34
NUM LOCK 35
KEYBOARD SETTING 36
CONTROL CHARACTER EMULATION 38
PEN EMULATION 39
OPERATING MODE 40
MINIMUM OUTPUT PULSE 41
CONVERSION TO CODE 39 42
OVERFLOW 42
OUTPUT LEVEL 43
IDLE LEVEL 43
INTER-BLOCK DELAY 43
DATA FORMAT 44
CODE IDENTIFIER 46
CUSTOM CODE IDENTIFIER 46
four character header 47
TERMINATOR 48
SPECIAL KEYS 48
FIELD ADJUSTMENT 50
FIELD ADJUSTMENT CHARACTER 51
CODE LENGTH TX 51
CHARACTER REPLACEMENT 52
POWER SAVE 54
SLEEP STATE 55
ENTER SLEEP TIMEOUT 55
READING PARAMETERS 56
TRIGGER TYPE 57
TRIGGER SIGNAL 57
TRIGGER CLICK 57
TRIGGER-OFF TIMEOUT 58
FLASH MODE 58
READS PER CYCLE 58
SAFETY TIME 59
BEEPER INTENSITY 59
BEEPER TONE 60
BEEPER TYPE 60
BEEPER LENGTH 60
GOOD READ SPOT DURATION 61
AIMING SYSTEM 61
DECODING PARAMETERS 62
INK SPREAD 63
OVERFLOW CONTROL 63
INTERDIGIT CONTROL 63
DECODING SAFETY 64
PUZZLE SOLVER™ 64
CODE SELECTION 65
Ì#+AUTOWÎ 66
EAN/UPC FAMILY 68
ÌAA8Ad03Î 69
ÌAA8Ad19Î 69
2/5 FAMILY 74
CODE 39 FAMILY 75
CODE 128 FAMILY 76
CODE 93 77
CODABAR FAMILY 77
CODE 11 80
CODE 16K 81
CODE 49 81
GS1 DATABAR™ CODES 82
CONCATENATION 84
ADVANCED FORMATTING 100
4 REFERENCES 102
4.1.2 ACK/NACK Protocol 103
4.1.3 FIFO 103
4.2 PEN PARAMETERS 104
4.2.1 Minimum Output Pulse 104
4.2.3 Overflow 104
4.1.4 RX Timeout 104
4.2.5 Inter-Block Delay 105
4.3 DATA FORMAT 105
Enter Configuration 107
Exit and Save Configuration 107
REFERENCES 109
WLS8600 110
ÌFQ9C2>Î 112
4.4 POWER SAVE 115
4.4.1 Sleep State 115
4.4.2 Enter Sleep Timeout 115
4.5 READING PARAMETERS 116
4.5.1 Trigger Signal 116
4.5.2 Trigger Click 116
4.5.3 Trigger-Off Timeout 116
4.5.4 Reads per Cycle 116
4.5.5 Safety Time 117
4.6 DECODING PARAMETERS 117
4.6.1 Ink-Spread 117
4.6.2 Overflow Control 117
4.6.3 Interdigit Control 118
4.7 ADVANCED FORMATTING 118
4.7.1 Match Conditions 118
Ì$+$*oÎ 119
Ì$+$!KÎ 119
Ì$+$&_Î 119
Ì$+$0ÂÎ 120
Ì$+$1$Î 120
Ì#+CODEÂÎ 120
Ì$+ZZ0$-*Î 121
5 TECHNICAL FEATURES 123
5.2 STATUS INDICATORS 124
5.3 READING TABLE 125
SERIAL CONFIGURATION STRINGS 126
(not for USB-KBD-ALT-MODE) 128
(IBM AT compatible only) 128
B CODE IDENTIFIER TABLE 137
C HEX AND NUMERIC TABLE 140
Wasp Barcode Technologies 144
1400 10th Street 144
Plano, Texas USA 75074 144

Commentaires sur ces manuels

Pas de commentaire

Wasp-barcode WLS8600 Product Reference Guide Manuel d'utilisateur Page 19

Commentaires sur ces manuels